浅谈环境水质分析结果的审核工作

对分析结果的有效数字和数据之间的合理性关系问题从理论上进行了研究,为数据审核工作提供科学参考。     

Orientation relationship in various 9%Cr ferritic/martensitic steels–EBSD comparison between Nishiyama–Wassermann,Kurdjumov–Sachs and Greninger–Troiano

EBSD measurements were carried out on four different martensitic steels (T91, P92, EM10 and Eurofer) in various metallurgical conditions (nine different microstructural states). The usual orientation relationships (ORs) between the parent austenitic phase and the resulting martensite in martensitic steels are those of Nishiyama–Wassermann (NW) and Kurjumov–Sachs (KS). The present study first proposes a methodology based on the combined analysis of the misorientation distribution, the pole figures (PFs) and the angle/axis pairs. This methodology leads to the conclusion that neither NW nor KS relationships are able to account for all the features observed whatever the material under study. A third OR proposed by Greninger and Troiano (GT) proves to describe the relationship between austenite and ferrite in all four different martensitic steels much more accurately.     

孔隙率及晶粒尺寸对多孔PZT陶瓷介电和压电性能的影响及机理研究

采用添加造孔剂的方法制备多孔锆钛酸铅(PZT)陶瓷，并研究了孔隙率和晶粒尺寸对多孔PZT陶瓷介电和压电性能的影响及机理.研究表明：孔隙率的增加降低了多孔PZT陶瓷的介电常数，提高了静水压优值，并证明在一定条件下孔隙率与介电常数关系可由Okazaki经验公式及Banno模型预测；晶粒尺寸增加，多孔PZT陶瓷的介电常数、压电系数和优值增加，并可用Okazaki空间电荷理论解释晶粒尺寸对试样介电和压电性能的影响.对于添加重量百分数为10%造孔剂的多孔PZT陶瓷，当烧结温度为1300℃时，孔隙率为34%，d关键词： 多孔PZT陶瓷 静水压优值 压电性能 介电性能     

Polystyrene comb polymers built on cellulose or poly(styrene-co-2-hydroxyethylmethacrylate) backbones as substrates for the preparation of structured honeycomb films

Comb polymers were prepared using the RAFT process via a Z-group approach. Trithiocarbonate RAFT agents were covalently bound to a polymer backbone via ester linkages. Two different types of comb polymer backbones were prepared, based on either modified cellulose or statistical poly(styrene-co-2-hydroxyethylmethacrylate) backbones. The subsequent polymerization of styrene from these multi-RAFT-functional backbones displayed some unusual kinetics with the rate of polymerization increasing concomitantly with the trithiocarbonate concentration. The molecular weight of each polystyrene branch increased with conversion, however, deviation from the theoretical molecular weight was detected. The polystyrene comb polymers were utilized in a casting process to prepare highly regular honeycomb structured porous films using breath figures. In general, the regularity was found to increase with increasing number of branches on a backbone and with increasing length of the polystyrene branch.     

用激光显示李萨如图形

介绍用电磁打点计时器通过激光显示李萨如图形的简单方法．     

Directional Photomanipulation of Breath Figure Arrays

Porous polymeric films are of paramount importance in many areas of modern science and technology. However, processing methods typically based on direct writing, imprint, and lithography techniques have low throughput and are often limited to specific fabricated shapes. Herein, we demonstrate the directional photomanipulation of breath figure arrays (BFAs) formed by an azobenzene‐containing block copolymer to address the aforementioned problems. Under the irradiation of linearly polarized light, the round pores in the BFAs were converted to rectangular, rhombic, and parallelogram‐shaped pores in 30 min, due to the anisotropic mass migration based on the photo‐reconfiguration of the azobenzene units. Through a secondary irradiation after rotating the sample by 90°, the transformed pores were apparently recovered. Therefore, this non‐contacted, directional photomanipulation technique in conjunction with breath figure processing opens a new route to nano/microporous films with finely tuned features.